InstructionManualISPC123BA 10/07 USAvoid injury or death -Read and understand this manual!
LATCH belt must be routed throughopening in child restraint for rear-facing mode.(see page 23, fig. k).Belt must lay flat and not be twisted.Adjust ch
(fig. c)(fig. d)9REAR-FACING INSTALLATION WITH LATCH(continued):(fig. b)(fig. e)OpeningsTowels(fig. f)TetherLATCHLAPC0110A(fig. a)Recline positionRecl
LATCH belt must be routed throughopening in child restraint for forward-facing(see page 23, fig. l).Belt must lay flat and not be twisted.Adjust car s
Openings(fig. c)(fig. d)11FORWARD-FACING INSTALLATION WITH LATCH(continued):(fig. b)(fig. f)(fig. e)(B)(A)Pull totightenTetherLATCH(fig. a)UprightPosi
Pull front to back and left to right to check forsecure installation (fig. d). Vehicle lap beltMUST stay tight.If not secure, see “Vehicle Seat Belts”
REAR-FACING INSTALLATION WITH VEHICLE SEAT BELTS(continued):13(fig. c)(fig. d)Installation withLap belt only(fig. a)(fig. b)Recline positionOpeningsTo
Store LATCH belt by attaching to connectorsthrough rear-facing openings(see page 25, fig. q).• Attach connectors to storage bar on eachside (fig. a).•
FORWARD-FACING INSTALLATION WITH VEHICLE SEAT BELTS(continued):(fig. c)(fig. d) (fig. e)Openings15(fig. a)(fig. f)(B)(A)Pull totightenLATCH (stored)Te
Check harness system:• Rear-facing - 5-30 lbs (2.2-13.6 kg)Harness straps must bethrough bottom or middleslots at or below shoulders.• Forward-facing
172335-PointModelsOverheadShieldModels(fig. a)2(fig. b)PLACING CHILD IN CHILD RESTRAINT (continued)44
TABLE OF CONTENTSImportant Information...1Warnings...2Basic Info
OPERATIONS and ADJUSTMENTS18Recline / Upright Positions (fig. b):Rear-facing - MUST use Recline position.Forward-facing - MUST use Upright positionUpr
195-PointModels(fig. a)(fig. d)OverheadShieldModels(fig. c)OPERATIONS and ADJUSTMENTS (continued)ClipUpper Tab(to loosen)Lower Belt(to tighten)1234123
20Changing Harness Strap Slots:A Loosen harness straps:Pull and hold upper belt tab.Pull harness straps out.B Remove both shoulder harness straploops
215-PointModelsOverheadShieldModels(fig. e)(fig. f)BottomLoopLoopSplitter PlateTopLoopOPERATIONS and ADJUSTMENTS (continued)(fig. g)Stand
22LATCH Belt Routing:LATCH belt MUST be routed throughthe proper openings depending on directionof child restraint use.A Remove pad from front of seat
OPERATIONS and ADJUSTMENTS (continued)23Route LATCH belt through Rear-facingopenings for:• LATCH Rear-facing use.or• LATCH storage with Forward-facing
24OPERATIONS and ADJUSTMENTS (continued)Removing LATCH from VehicleAnchor Points:A Tilt metal tab of adjuster to release tension(fig. m).Press down on
25OPERATIONS and ADJUSTMENTS (continued)LATCH storage:• Locate LATCH storage bars under arm reston sides of child restraint (fig. p).• Fasten LATCH on
26VEHICLE SEAT BELTSTo provide the most secure installation of thechild restraint:• Read the vehicle owner’ s manual regardingchild restraint installa
Vehicle seat belts located forward of seatcrease may not securely hold child restraint.Check vehicle owner’ s manual or see vehicledealer for car seat
IMPORTANT INFORMATIONNo child restraint can guarantee protectionfrom injury in every situation, but proper usehelps reduce the risk of serious injury
28Lap belts with retractors may or may not holda child restraint securely.Follow these steps to determine if you have aretractor system that will hold
DO NOT use with any child restraint.>Passive Restraint - Lap Beltwith Motorized Shoulder BeltDO NOT use with any child restraint. Belts willnot sta
30Pull on latch plate (fig. a). If belt slides freelythrough latch plate, a locking clip MUSTbe used (see Pg. 31 “Locking Clip” section).Some combinat
1/2 inch (1 cm)(fig. a)VEHICLE SEAT BELTS (continued)Avoid serious injury or death:• Failure to use locking clip whererequired will result in childres
32ADDITIONAL INFORMATIONDO NOT anchor tether strap to the vehiclewhen using child restraint rear-facing.Tether hook must be attached to child restrain
33Available on some models:• Insert the two prongs of the cupholder intothe two slots on either the left or right side ofthe seat.• Push cupholder dow
34ADDITIONAL INFORMATION (continued)>Body Pillow(available on some models)Push top of bodypillow in betweenharness straps andfit into seat exactlya
>Head Support(available on some models)ADDITIONAL INFORMATION (continued)Position Head Support in center of car seatwith ends pointing down and ins
>Head Support(available on some models)To prevent ejection in suddenstop or crash:• Shoulder straps must be threadedthrough slots and properlyposit
ADDITIONAL INFORMATION (continued)>Harness Covers(available on some models)HarnessCovers37• Make sure the harness system isproperly secured.• Check
WARNINGS - Prevent serious injury or death:Failure to follow these instructionsand child restraint labels can resultin child striking the vehicle’ s i
38Removing Seat Pad (all models):Remove both harness strap loops fromSplitter Plate on back of child restraint andpull through front of pad. Open harn
39ADDITIONAL INFORMATION (continued)Seat Pad and Overhead Shield Pad:Remove the plastic 2-button clips.Machine-wash separately on gentle cycleand drip
NOTES41
Store instruction manualbehind this tab.Store locking cliphere.Fold instruction manual.12Graco Children’ s Products Inc.A Division of Newell Rubbermai
Evite lesiones o la muerte -¡ Lea detenidamente este manual!ISPC123BA 10/07 USManual deinstrucciones
TABLA DE CONTENIDOInformación importante ...1Advertencia ...2Información
INFORMACIÓN IMPORTANTENingún asiento de seguridad garantiza laprotección contra lesiones en cualquier situación,pero su utilización correcta ayuda a r
ADVERTENCIA - Prevenga lesiones graves o la muerte:El incumplimiento de estasinstrucciones y de las indicaciones delas etiquetas del asiento podrí aca
3NO retire el sistema LATCHdel asiento de seguridad. Si usa elcinturón de seguridad del vehí culopara sujetar el asiento de seguridad,debe almacenar l
3If child restraint is in a crash, itmust be replaced. DO NOT use itagain! A crash can cause unseendamage and using it again couldresult in serious in
INFORMACIÓN BÁSICAEste asiento de seguridad cumple o excede todos losrequisitos requeridos por la Norma Federal 213 deSeguridad de Automóviles para us
5Puntos deanclajesuperior delvehículoPuntos de anclajeinferior delvehí culoPliegue delasiento delvehí culoAsiento tí picoen un vehí culo depasajeros.
6El sistema LATCH:El LATCH consta de un cinturónde anclaje inferior permanente yuna correa de anclajesuperior (Fig. a).Utilice con LATCH ÚNICAMENTEen
*La American Academy of Pediatrics recomiendaque los niños tengan un año de edad como mínimopara poder sentarse orientados hacia delante.LÍMITES DE AL
El cinturón LATCH debe pasar por laapertura del asiento de seguridaddestinada al modo de orientación trasera.(vea la página 23, fig. k).El cinturón de
(fig. c)(fig. d)9INSTALACIÓN ORIENTADA HACIA ATRÁS CON LATCH(fig. b)(fig. e)AperturasToallas(fig. f)AnclajeLATCHLAPC0110APosiciónreclinada(fig. a)Posi
El cinturón LATCH debe pasar por laapertura del asiento de seguridad destinadaal modo de orientación delantera(vea la página 23, fig. l).El cinturón d
Aperturas(fig. c)(fig. d)11INSTALACIÓN ORIENTADA HACIA DELANTE CON LATCH(fig. b)(fig. f)(fig. e)(B)(A)Jale paraapretarAnclajeLATCH(fig. a)Posiciónvert
Jálela de atrás hacia delante y de izquierda aderecha para asegurarse de que estáperfectamente instalado (fig. d). El cinturón deregazo del vehí culo
(fig. a)AperturasToallas13(fig. c)(fig. d)Barra dealmacenajeAnclajeLATCH (almacenar)INSTALACIÓN DE ORIENTACION TRASERACON LOS CINTURONES DE SEGURIDAD
BASIC INFORMATIONThis child restraint meets or exceeds allapplicable requirements of Federal MotorVehicle Safety Standard 213 for use in motorvehicles
Presione fuertemente en el centro del asientode seguridad para comprimir el cojí n delasiento del vehí culo al tiempo que aprieta elcinturón de seguri
INSTALACIÓN ORIENTADA HACIA DELANTE CONLOS CINTURONES DE SEGURIDAD DEL VEHÍCULO(fig. c)(fig. d) (fig. e)Aperturas15(fig. a)(fig. f)(B)(A)Jale paraapre
Compruebe el sistema del arnés:• Orientado hacia atrás - 5 a 30 libras(2.2 a 13.6 kg) Las correas del arnés debenpasar por las ranuras inferiores o me
17(fig. a) (fig. b)COLOCAR AL NIÑO EN EL ASIENTO DE SEGURIDAD233Modelos de5 puntosModelos conbarra protectora244
OPERACIONES Y AJUSTES18Posiciones reclinada / vertical (fig. b):Orientado hacia atrás -SE DEBE usar la posición reclinada.Orientado hacia delante -SE
19Modelos de5 puntos(fig. a)(fig. d)Modelos conbarra protectora(fig. c)OPERACIONES Y AJUSTESClip12341234Lengüetasuperior(parasoltar)Cinturóninferior(p
20Cambiar las ranuras de las correas del arnés:A Suelte las correas del arnés:Jale la lengüeta superior del cinturóny sosténgala al tiempo que jala la
21Modelos de5 puntosModelos conbarra protectora(fig. e)(fig. f)BucleinferiorBuclePlaca de uniónBuclesuperiorOPERACIONES Y AJUSTES(fig. g)Soporte
22Colocación del cinturón LATCH:El cinturón LATCH DEBE pasar por lasaperturas adecuadas según laorientación del asiento.A Quite la almohadilla de la p
OPERACIONES Y AJUSTES23Pase el cinturón LATCH por las aperturas deorientación hacia atrás para:• usar el sistema LATCH orientado hacia atrás.o• Almace
5VehicleTop Tether AnchorPointsVehicleLower AnchorPointsVehicleSeat CreaseTypical seat in apassenger vehicle.Other vehicle typesmay have differentLATC
24OPERACIONES Y AJUSTESRetirar el LATCH de los puntos de anclajedel vehí culo:A Incline la lengüeta metálica del dispositivode ajuste para soltar la t
25OPERACIONES Y AJUSTESAlmacenaje LATCH:• Ubique las barras de almacenaje LATCHdebajo la almohadilla del asiento enel lado del asiento de seguridad in
26CINTURONES DE SEGURIDAD DEL VEHÍCULOPara lograr la instalación del asiento de seguridadmás segura:• Lea la sección del manual del propietario delveh
Los cinturones de seguridad del vehí culo ubicadosdelante del pliegue en el asiento quizá no sujetenbien el asiento. Consulte el manual del propietari
28Los cinturones de regazo con retractor pueden o nosujetar el asiento firmemente.Siga estos pasos para determinar si su sistema deretractor que sujet
NO SE DEBE usar con ningún asiento.NO SE DEBE usar con ningún asiento.Los cinturones no se mantendrán apretadosdurante el manejo del auto.>Cinturón
30Jale la placa de cierre (fig. a). Si el cinturón sedesliza fácilmente por la placa de cierre, SE DEBEutilizar un clip de cierre (vea la sección &quo
1/2 pulgada(1 cm)(fig. a)CINTURONES DE SEGURIDAD DEL VEHÍCULOADVERTENCIA>Clip de cierreCompruebe la instalación para ver si el asientoha quedado bi
32INFORMACIÓN ADICIONALNO conecte la correa de anclaje superior al vehí culoal utilizar el asiento orientado hacia atrás.El gancho del anclaje debe co
Disponible en ciertos modelos:• Inserte las dos clavijas del apoya vasosen las dos ranuras del costado izquierdo oderecho del asiento.• Empuje el apoy
6LATCH System:LATCH consists of a permanently attachedlower anchorage belt and a top tether strap(Fig. a).ONLY use LATCH in a seatingposition recommen
34> El cojín del cuerpo(Disponible en algunos modelos)Empuje la parte dearriba del cojí n delcuerpo entre lascorreas del arnés ypóngalo en el asien
35INFORMACIÓN ADICIONAL>Soporte de la cabeza(Disponible en algunos modelos)¡ Para usarse solamente con lasranuras superiores y centrales delarnés!
>Soporte de la cabeza(Disponible en algunos modelos)Para prevenir la eyección en unaccidente o parada repentina, lascorreas del hombro deben pasar
INFORMACIÓN ADICIONAL>Cubiertas del arnés(available on some models)Cubiertasdel arnés37• Asegúrese de que el sistema delarnés esté asegurado correc
38Retirar la almohadilla (todos los modelos):Retire los dos bucles de las correas del arnés de laplaca de unión de la parte trasera del asiento ypásel
39INFORMACIÓN ADICIONALLas almohadillas del asiento y de labarra protectora:Saque las dos trabas de 2 botones de plástico.Se lavan a máquina por separ
40NOTAS
NOTAS41
Guarde el manual de instruccionesdetrás de estas lengüetas.Guarde aquí elclip de cierre.Doble el manual de instrucciones.1 2Graco Children’ s Products
© 2003 Graco ISPC063BA 08/03To prevent ejection in sudden stop or crash: • Make sure that the harness system is properly secured and shoulder straps
HEIGHT & WEIGHT LIMITSA preterm infant or low birth weight infant maybe at special risk in a vehicle or aircraft.According to the American Academy
STEP 2.Push harness behind seat pad asshown. Repeat on other side of pad.Push crotch strap through seat pad.2STEP 4.Remove 2 plastic clips at front ba
© 2003 Graco ISPC063BA 08/03Para prevenir la eyección en un accidente o frenada repentina: • Asegúrese de que el sistema del arnés estédebidamente a
PASO 2.Empuje el arnés detrás de la almohadilla del asiento como se indica. Repita el procedimiento delotro lado de la almohadilla.Empuje la correa de
Comments to this Manuals