Graco 313998S User Manual Page 27
- Page / 94
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Repair
313998S 27
Remove HFR Hydraulic Driver
This procedure removes the HFR Hydraulic Driver so
replacement parts can be installed. See HFR Hydraulic
Driver manual for replacement parts installation proce-
dure.
1. Perform Remove Chemical Pumps procedure, see
page 24.
2. Disconnect the fluid manifold inlet lines. Do not dis-
connect the fluid line connections at the heater.
3. Remove pump support brackets. Each bracket is
secured with three screws at the base frame and
two screws at the manifold bracket.
4. See FIG. 4. Remove four nuts (188) securing
hydraulic driver to hydraulic power pack. This will
also loosen manifold plate (104) from hydraulic
driver. Remove manifold plate. Remove hydraulic
driver.
Install HFR Hydraulic Driver
This procedure installs the hydraulic driver after replace-
ment parts have been installed and actuator has been
reassembled. See HFR Hydraulic Driver manual for
replacement parts installation procedure.
1. Hang the hydraulic driver on the studs. Verify o-rings
between driver and hydraulic power pack are
installed and lubricated. Secure the driver with nuts
and washer at bottom-left and top-right corners.
2. Install manifold bracket. Secure at top-left and bot-
tom-right corners.
3. Install pump suppor t brackets, torque to 300 in-lb
(33.9 N•m). This will also install manifold plate (104)
to hydraulic driver.
4. Connect fluid manifold inlet lines.
5. Perform Install Chemical Pumps procedure, see
page 26.
FIG.4
155
104
156
124
125
155
188
156
112
111
180
24C352_313998_5g1
Fluid Manifold Inlet
24C352_313998_4e1
- Repair - Parts 1
- Contents 2
- Related Manuals 3
- 400 V Power Requirements 4
- 6 313998S 6
- Whip Hose Bundles 7
- B (Blue) Individual 8
- A (Red) Individual 9
- Hose Bundling Accessories 10
- Applicator 10
- B (Blue) Applicator Orifice 11
- S-Head and L-Head 12
- AC Power Pack with 13
- S-Head/L-Head Hoses, Optional 13
- Dispense Valve Interface Kit 13
- Pump Feed Kits 14
- Flow Meters 14
- Product Configurator 15
- 313998S 15 15
- Additional Accessories 16
- Warnings 17
- 18 313998S 18
- Isocyanate Conditions 19
- Material Self-ignition 19
- Keep Components A (Red) and 19
- B (Blue) Separate 19
- Moisture Sensitivity of 20
- Isocyanates 20
- Foam Resins with 245 fa 20
- Blowing Agents 20
- Changing Materials 20
- Shutdown 21
- Pressure Relief Procedure 22
- Flushing 23
- Pumpline 24
- 313998S 25 25
- Install Chemical Pumps 26
- Prime IsoGuard Select 26
- Cylinder 26
- Remove HFR Hydraulic Driver 27
- Install HFR Hydraulic Driver 27
- Remove PowerHouse Pumpline 28
- FIG. 7. Remove pumpline 29
- Install PowerHouse Pumpline 30
- 313998S 31 31
- Hydraulic Power Pack Repair 32
- Replace Hydraulic Filter 33
- Replace Fan 33
- Remove Motor Control Module 33
- 34 313998S 34
- Install Motor Control Module 35
- Remove Hydraulic Power Pack 35
- Install Hydraulic Power Pack 36
- Replace Tank Gasket, Tank 36
- Remove Motor 36
- Install Motor 37
- Remove Hydraulic Gear Pump 37
- Install Hydraulic Gear Pump 37
- 38 313998S 38
- Base Machine 39
- Torque to 300 in-lb (34 N•m) 40
- Torque to 79 in-lb (8.9 N•m) 40
- Torque to 62 in-lb (7.0 N•m) 40
- Torque to 150 in-lb (17 N•m) 40
- Torque to 17 ft-lb (23 N•m) 41
- 24C352_313998_9e 43
- 44 313998S 44
- Base Machine Sub-Assemblies 47
- 48 313998S 48
- 313998S 49 49
- A Side Shown 50
- SST Fluid Inlet Assemblies 51
- Power Pack Module 52
- 313998S 53 53
- 313998S 55 55
- Heat Exchanger Assembly 56
- Heater Options 57
- 24C327_313998_1L 58
- 24C327_313997_9f 58
- 24C327_313998_2L 58
- 313998S 61 61
- 62 313998S 62
- 313998S 63 63
- 64 313998S 64
- Heater Sub-Assemblies 65
- 66 313998S 66
- 313998S 67 67
- 68 313998S 68
- 313998S 69 69
- Heater 24J787 70
- 313998S 71 71
- 72 313998S 72
- DC Power Pack Hydraulic 73
- Pressure Adjustment Setup 73
- Logic Drawings 74
- 230V, 1 Phase, with Heat 75
- 76 313998S 76
- 230V, 3 Phase, No Heat 77
- 230V, 3 Phase, with Heat 78
- 313998S 79 79
- 400V, 3 Phase, No Heat 80
- 400V, 3 Phase, with Heat 81
- 82 313998S 82
- A (Red) Heat 83
- LOCATED IN THE MAIN 84
- SUPPORT ENCLOSURE 84
- B (Blue) Heat 85
- B - BLUE 86
- DC Hydraulic Power Pack 87
- Motor Control Module (MCM) 88
- 313998S 89 89
- Miscellaneous Power 90
- FOR VARIABLE RATIO ONLY 91
- TERMINAL STRIP MOUNTED 91
- ON BACKPANEL 91
- Technical Data 92
- 313998S 93 93
- Graco Standard Warranty 94
- Graco Information 94
Related products and manuals for Paint Sprayer Graco 313998S
Paint Sprayer Graco 310543E User Manual
(20 pages)
(20 pages)
Paint Sprayer Graco 307637R User Manual
(10 pages)
(10 pages)
Paint Sprayer Graco 313255K User Manual
(34 pages)
(34 pages)
Paint Sprayer Graco 312779E User Manual
(134 pages)
(134 pages)
Paint Sprayer Graco 309923F User Manual
(8 pages)
(8 pages)
Paint Sprayer Graco 311827G User Manual
(20 pages)
(20 pages)
Paint Sprayer Graco 311287E User Manual
(92 pages)
(92 pages)
Paint Sprayer Graco 308842H User Manual
(24 pages)
(24 pages)
Paint Sprayer Graco 332564B User Manual
(104 pages)
(104 pages)
Paint Sprayer Graco 312065M User Manual
(42 pages)
(42 pages)
Paint Sprayer Graco 3A0538F User Manual
(30 pages)
(30 pages)
Paint Sprayer Graco 308666C User Manual
(8 pages)
(8 pages)
Paint Sprayer Graco 312062W User Manual
(52 pages)
(52 pages)
Paint Sprayer Graco 312793H User Manual
(24 pages)
(24 pages)
Paint Sprayer Graco 309951E User Manual
(10 pages)
Paint Sprayer Graco 3W9250N User Manual
(10 pages)
(10 pages)
Paint Sprayer Graco 3A0158F User Manual
(20 pages)
(20 pages)
Paint Sprayer Graco 311305E User Manual
(14 pages)
(14 pages)
© 2020, manymanuals.com. All rights reserved. | 1.018 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals